Korean Journal of Materials Research, Vol.25, No.9, 442-449, September, 2015
최적 고속화염용사법으로 제조된 Diamalloy4006 코팅의 내마모 특성
Wear Property of Diamalloy-4006 Coating Prepared by OCP HVOF Thermal Spraying
E-mail:
The effects of coating parameters were investigated in wear resistance coatings of Diamalloy-406 on Inconel 718 to obtain an optimum coating condition by high velocity oxy-fuel spraying. The coating parameters, the flow rates of source gases (hydrogen and oxygen), the powder feed rate, and the spray distance, were designed by the Taguchi method. The optimal conditions were determined: oxygen flow rate 34 FRM, hydrogen flow rate 57 FRM, powder feed rate 35 g/min, and spray distance 7 inch. Friction coefficients of the coating and the substrate decreased with an increasing sliding surface temperature from 25 oC to 450 oC. The friction coefficient of Diamalloy-4006 coating decreased as the sliding surface temperature increased from 0.43 ± 0.01 at 25 oC to 0.29 ± 0.01 at 450 oC. The wear trace and wear depth of the coating were smaller than the substrate at all temperatures tested. The relationship between spray parameters and wear resistance was discussed extensively, based on the measured roughness, hardness, and porosity in each coating.
- Kim HM, Jin HW, Choi SJ, Kwon SJ, Park CG, J. Korea Inst. Met. Mater., 38, 125 (2000)
- Davis JR, ASM International, p.1-30, USA, (2004).
- Park SY, Park CG, J. Korea Inst. Met. Mater., 42, 582 (2004)
- Lim BM, Hong SH, Jeong JI, J. Kor. Inst. Met. Mater., 41, 677 (2003)
- Ahn JH, Hwang BC, Song EP, Lee SH, Kim NJ, J. Korea Inst. Met. Mater., 43, 433 (2005)
- Berndt CC, Lenling WJ, (2005), “Handbook of Thermal Spray Technology”, US. ASM International, pp. 1-13.
- Celik E, Culha O, Uyulgan B, Azem NFA, Ozdemir I, Turk A, Surf. Coat. Technol., 200, 4320 (2006)
- Wank A, Wielage B, Pokhmurska H, Friesen E, Reisel G, Surf. Coat. Technol., 201, 1975 (2006)
- Mason RL, Gunst RF, Hess JL, "Statistical Design and Analysis of Experiments, second Edition", A John Wiley and Sons Publication, Hoboken, New Jersey, pp. 406-409, 2003.
- Yusoff N, Ramasamy M, Yusup S, Chem. Eng. Res. Des., 89(6), 665 (2011)
- Kaushik G, Thakur IS, Int. Biodeterior. Biodegrad., 63(4), 420 (2009)
- Bolelli G, Cannillo V, Lusvarghi L, Ricco S, Surf. Coat. Technol., 200, 2995 (2006)
- Hawthorne HM, Arsenault B, Immarigeon JP, Legoux JG, Parameswaran VR, Wear, 225-229, 825 (1999)
- Cho TY, Yoon JH, Kim KS, Bak NK, Song KO, Youn SJ, Hwang SY, Chun HG, J. Korea Inst. Surf. Eng., 39, 295 (2006)
- Cho TY, Yoon JH, Kim KS, Park BK, Youn SJ, Back NK, Chun HG, J. Korea Cryst. Growth Cryst. Technol., 16, 121 (2006)
- Kawakita J, Kuroda S, Fukushima T, Kodamaet T, Corrosion Sci., 45, 2819 (2003)
- Bolelli G, Lusvarghi L, Giovanardi R, Surf. Coat. Technol., 202, 4793 (2008)
- Massalski TG, Am. Soc. Met., 1, 600 (1986)
- Song KO, Cho TY, Yoon JH, Fang W, Youn SJ, Suh CH, Youn KT, Hwang SY, Ha SS, J. Korea Inst. Met. Mater., 46, 351 (2008)