화학공학소재연구정보센터

Polymer Engineering and Science

Polymer Engineering and Science, Vol.48, No.4 Entire volume, number list
ISSN: 0032-3888 (Print) 

In this Issue (25 articles)

627 - 633 Effects of thermal aging on isotactic polypropylene crystallinity
Law A, Simon L, Lee-Sullivan P
634 - 641 Effect of annealing and orientation on microstructures and mechanical properties of polylactic acid
Yu L, Liu HS, Xie FW, Chen L, Li XX
642 - 648 Oxygen permeability of biaxially oriented polypropylene films
Lin YJ, Dias P, Chen HY, Chum S, Hiltner A, Baer E
649 - 655 Solid-state blending of poly(ethylene terephthalate) with polystyrene: Extent of compatibilization and its dependence on blend composition
Schexnaydre RJ, Mitchell BS
656 - 661 Rheological characterization of room temperature vulcanized silicone sealant: Effect of filler particle size
Xu XM, Gao CH, Zheng Q
662 - 675 Condensed-phase flame retardation in nylon 6-layered silicate nanocomposites: Films, fibers, and fabrics
Shanmuganathan K, Deodhar S, Dembsey NA, Fan QG, Patra PK
676 - 682 Compression hysteresis of fibrous systems
Stankovic SB
683 - 686 Foam formation from fluorinated polyphosphazenes by liquid CO2 processing
Steely LB, Li QX, Badding JV, Allcock HR
687 - 696 Improved through-plane electrical conductivity in a carbon-filled thermoplastic via foaming
Motlagh GH, Hrymak AN, Thompson MR
697 - 704 Effect of molecular weight and molding conditions on the replication of injection moldings with micro-scale v-groove features
Murakami O, Kotaki M, Hamada H
705 - 710 Fibril formation of 1,3 : 2,4-di(3,4-dimethylbenzylidene) sorbitol in polymer melts
Lipp J, Shuster M, Terry AE, Cohen Y
711 - 716 Advanced injection molding mold and molding process for improvement of weld line strengths and isotropy of glass fiber filled aromatic polyester LCP
Koponen M, Enqvist J, Nguyen-Chung T, Mennig G
717 - 722 Local thermo-oxidative degradation in injection molding
Schmiederer D, Gardocki A, Kuhnert I, Schmachtenberg E
723 - 731 Characterization of new formulations for the rotational molding based on ethylene-propylene copolymer/graphite nanocomposites
Planes E, Duchet J, Maazouz A, Gerard JF
732 - 746 Effects of welding procedures on mechanical and morphological properties of hot gas butt welded PE, PP, and PVC sheets
Balkan O, Demirer H, Ezdesir A, Yildirim H
747 - 755 Yield stress and rheological characterization of the low shear zone of an epoxy molding compound for encapsulation of semiconductor devices
Yoshii M
756 - 766 A comparative study of dispersing a polyamide 6 into a polypropylene melt in a Buss Kneader, continuous mixer, and modular intermeshing corotating and counter-rotating twin screw extruders
Shon K, Bumm SH, White JL
767 - 773 Simulation of the residual stresses in the contour laser welding of thermoplastics
Potente H, Wilke L, Ridder H, Mahnken R, Shaban A
774 - 785 Calculation and significance of the maximum polymer surface temperature T* in reciprocating cylinder-on-plate sliding
Samyn P, Schoukens G
786 - 794 Determination of different morphological structures in PC/ABS open spiral injection moldings
O-Charoen N, Leong YW, Hamada H
795 - 805 Synthetic 6FDA-ODA copolyimide membranes for gas separation and pervaporation: Correlation of separation properties with diamine monomers
Xiao SD, Feng XS, Huang RYM
806 - 814 In-line measurements of the morphological parameters of PP/PA6 blends during extrusion in the transient mode
Pinheiro LA, Hu GH, Pessan LA, Canevaro SV
815 - 822 The mastication characteristics of powdered carbon black filled natural rubber during internal mixing
Zhang AQ, Lin YL, Wang LS
823 - 828 Synthesis and characterization of hollow polyaniline microtubes and microbelts with nanostructured walls in sodium dodecyl sulfate micellar solutions
Wu TM, Lin YW
829 - 836 Thermal degradation and physical aging of poly(lactic acid) and its blends with starch
Acioli-Moura R, Sun XS