화학공학소재연구정보센터

Minerals Engineering

Minerals Engineering, Vol.24, No.3-4 Entire volume, number list
ISSN: 0892-6875 (Print) 

In this Issue (26 articles)

179 - 180 Special issue: Comminution Foreword
Powell M
181 - 187 CFD-DEM modelling of particle flow in IsaMills - Comparison between simulations and PEPT measurements
Jayasundara CT, Yang RY, Guo BY, Yu AB, Govender I, Mainza A, van der Westhuizen A, Rubenstein J
188 - 194 A comparative study between cone crushers and theoretically optimal crushing sequences
Lee E, Evertsson CM
195 - 204 Tracking the motion of media particles inside an IsaMill (TM) using PEPT
van der Westhuizen AP, Govender I, Mainza AN, Rubenstein J
205 - 210 Simulation assisted capacity improvement of cement grinding circuit: Case study cement plant
Dundar H, Benzer H, Aydogan NA, Altun O, Toprak NA, Ozcan O, Eksi D, Sargin A
211 - 215 Comparison of the overall circuit performance in the cement industry: High compression milling vs. ball milling technology
Aydogan NA, Benzer H
216 - 220 A new method for determination of fine particle breakage
Eksi D, Benzer AH, Sargin A, Genc O
221 - 224 The effect of the design of a secondary grinding circuit on platinum flotation from a UG-2 ore
Maharaj L, Loveday BK, Pocock J
225 - 229 Measurement of shear rates in a laboratory tumbling mill
Govender I, Mangesana N, Mainza AN, Franzidis JP
230 - 235 Towards a mechanistic model for slurry transport in tumbling mills
Govender I, Tupper GB, Mainza AN
236 - 244 Prediction of mill structure behaviour in a tumbling mill
Jonsen P, Palsson BI, Tano K, Berggren A
245 - 251 Interpretation of mill vibration signal via wireless sensing
Das SP, Das DP, Behera SK, Mishra BK
252 - 260 Modeling breakage rates in mills with impact energy spectra and ultra fast load cell data
Tuzcu ET, Rajamani RK
261 - 266 Studies of the effect of tracer activity on time-averaged positron emission particle tracking measurements on tumbling mills at PEPT Cape Town
Volkwyn TS, Buffler A, Govender I, Franzidis JP, Morrison AJ, Odo A, van der Meulen NP, Vermeulen C
267 - 275 Comparison of open and closed circuit HPGR application on dry grinding circuit performance
Altun O, Benzer H, Dundar H, Aydogan NA
276 - 281 Characterising porosity of multi-component mixtures in rotary mills
Sichalwe K, Govender I, Mainza AN
282 - 289 Circulation rate modelling of mill charge using position emission particle tracking
Kallon DVV, Govender I, Mainza AN
290 - 302 A preliminary investigation into the feasibility of a novel HPGR-based circuit for hard, weathered ores containing clayish material
Rosario P, Hall R, Grundy M, Klein B
303 - 307 Investigation of the breakage of hard and soft components under high compression: HPGR application
Benzer H, Aydogan NA, Dundar H
308 - 318 Modeling breakage of monodispersed particles in unconfined beds
Barrios GKP, de Carvalho RM, Tavares LM
319 - 324 Power draw estimations in experimental tumbling mills using PEPT
Bbosa LS, Govender I, Mainza AN, Powell MS
325 - 334 Optimisation of the secondary ball mill using an on-line ball and pulp load sensor - The Sensomag
Keshav P, de Haas B, Clermont B, Mainza A, Moys M
335 - 340 Modeling the RTD of an industrial overflow ball mill as a function of load volume and slurry concentration
Makokha AB, Moys MH, Bwalya MM
341 - 351 DEM modelling of liner evolution and its influence on grinding rate in ball mills
Powell MS, Weerasekara NS, Cole S, LaRoche RD, Favier J
352 - 366 Understanding fine ore breakage in a laboratory scale ball mill using DEM
Cleary PW, Morrison RD
367 - 372 Effect of media size and mechanical properties on milling efficiency and media consumption
Farber BY, Durant R, Bedesi N