화학공학소재연구정보센터

Journal of Materials Science

Journal of Materials Science, Vol.41, No.13 Entire volume, number list
ISSN: 0022-2461 (Print) 

In this Issue (55 articles)

3959 - 3960 Preface - Syntactic and composite foams: Proceedings of an Engineering Conferences International (ECI) conference
Gladysz GM, Chawla KK
3961 - 3972 Structure and mechanical properties of micro and macro balloons: An overview of test techniques
Carlisle KB, Chawla KK, Gladysz GM, Koopman M
3973 - 3977 Characterization of pore size of trimethylol propane triacrylate (TMPTA) polymer foam by pulsed sputter coating and SEM analysis
Faith D, Horsfield CJ, Nazarov W
3979 - 3986 Foaming binary solution mixtures of low molecular surfactant and polyelectrolyte
Aidarova SB, Musabekov KB, Ospanova ZB, Guden M
3987 - 3997 Microstructure and compressive properties of carbon microballoons
Carlisle KB, Koopman M, Chawla KK, Kulkarni R, Gladysz GM, Lewis M
3999 - 4008 Poly(D,L-lactide) (PDLLA) foams with TiO2 nanoparticles and PDLLA/TiO2-Bioglass (R) foam composites for tissue engineering scaffolds
Boccaccini AR, Blaker JJ, Maquet V, Chung W, Jerome R, Nazhat SN
4009 - 4014 Microstructural failure modes in three-phase glass syntactic foams
Koopman M, Chawla KK, Carlisle KB, Gladysz GM
4015 - 4022 Shear properties of CMB syntactic foam
Chavez GM, Lewis MW, Lenke LR
4023 - 4039 Blast impact response of aluminum foam sandwich composites
Sriram R, Vaidya UK, Kim JE
4041 - 4046 Characterization of epoxy syntactic foams by dynamic mechanical analysis
Sankaran S, Sekhar KR, Raju G, Kumar MNJ
4047 - 4054 Hydrolytic ageing of syntactic foams for thermal insulation in deep water: degradation mechanisms and water uptake model
Sauvant-Moynot V, Gimenez N, Sautereau H
4055 - 4060 Dopeable styrenic foams used in inertial fusion targets
Steckle WP, Schoonover JR, Lanier NE, Nobile A
4061 - 4073 Experimental determination of the thermal conductivity of three-phase syntactic foams
Shabde VS, Hoo KA, Gladysz GM
4075 - 4084 SiC-particulate aluminum composite foams produced from powder compacts: foaming and compression behavior
Guden M, Yuksel S
4085 - 4092 Three-phase syntactic foams: structure-property relationships
Gladysz GM, Perry B, Mceachen G, Lula J
4093 - 4104 The double-torsion testing technique for determination of fracture toughness and slow crack growth behavior of materials: A review
Shyam A, Lara-Curzio E
4105 - 4116 Ballistic fibers: A review of the thermal, ultraviolet and hydrolytic stability of the benzoxazole ring structure
Holmes GA, Rice K, Snyder CR
4117 - 4121 Crystalline carbon nitride films prepared by microwave plasma chemical vapour deposition
Jiang JC, Cheng WJ, Zhang Y, Zhu HS, Shen DZ
4123 - 4131 Development of vapor grown carbon fibers (VGCF) reinforced carbon/carbon composites
Dhakate SR, Mathur RB, Dhami TL
4133 - 4136 Luminescent properties of YAl3(BO3)(4): Eu3+ phosphors
Yang H, Ren ZY, Cui YM, Yu LX, Feng SH
4137 - 4142 Effects of external electric field on microstructure and property of friction welded joint between copper and stainless steel
Fu L, Du SG
4143 - 4151 Characterisation methods for functionally graded materials
Tomandl G, Mangler M, Stoyan D, Tscheschel A, Freiberg TB, Goebbels J, Weidemann G
4153 - 4158 Direct ink-jet printing and low temperature conversion of conductive silver patterns
Smith PJ, Shin DY, Stringer JE, Derby B, Reis N
4159 - 4162 Hydroxyapatite forming ability of electrostatic spray pyrolysis derived calcium phosphate nano powder
Hwang KS, Jeon KO, Jeon YS, Kim BH
4163 - 4167 Preparation and characterization of LiMn2O4 and LiCo0.16Mn1.84O4 as cathode materials for lithium-ion batteries by low heating solid state coordination method
Huang YD, Li J, Jia DZ
4169 - 4177 Effect of thermal conductivity on reaction front propagation during combustion synthesis of intermetalics
Ballas M, Song H, Ilegbusi OJ
4179 - 4183 Influence of negative voltage on the structure and properties of DLC films deposited on NiTi alloys by PBII
Cheng Y, Zheng YF
4185 - 4190 Effect of Re-Nb on the strength and toughness of 3Cr2MoNiWV cast hot working die steel
Song YP, Mao XM, Wang WY, Ouyang ZY, Liang HY, Li LL
4191 - 4195 Formation characteristics of an aluminum hydroxide fiber by a hydrolysis of aluminum nano powder
Oh YH, Rhee CK, Kim DH, Lee GH, Kim WW
4197 - 4204 Porous methacrylate tissue engineering scaffolds: using carbon dioxide to control porosity and interconnectivity
Barry JJA, Silva MMCG, Cartmell SH, Guldberg RE, Scotchford CA, Howdle SM
4205 - 4213 Microstructure and ionic conductivity of Sr- and Mg-doped LaGaO3
Liu N, Shi M, Wang C, Yuan YP, Majewski P, Aldinger F
4215 - 4220 Preparation of composite particles coated with two kinds of solid powders by semi-chemical recycle method
Tanaka M, Taguchi Y, Sawatari N, Saito N
4221 - 4226 Microstructural development and electrical properties of lead zirconate titanate composite films
Chen ST, Wu JM, Yeh TS, Hu LJ
4227 - 4232 Microstructure and mechanical behavior of AlSiCuMgNi piston alloys reinforced with TiB2 particles
Zhao DG, Liu XF, Pan YC, Liu YX, Bian XF
4233 - 4237 Self-diffusion of transition metals in (Ti,W,Cr)B-2 solid solutions
Schmidt H, Borchardt G, Schmalzried C, Telle R, Baumann H, Weber S, Scherrer H
4239 - 4245 Nanoparticle-induced enhancement in fracture toughness of highly loaded epoxy composites over a wide temperature range
Han JT, Cho K
4247 - 4250 Spray-drying process for synthesis of nanosized LiMn2O4 cathode
Wu HM, Tu JP, Yang YZ, Shi DQ
4251 - 4258 Growth and characterization of partially oxidized platinum polymers in nanoscale templates
Anderson BM, Hurst SK, Spangler L, Abbott EH, Martellaro P, Pinhero PJ, Peterson ES
4259 - 4265 Effect of Al doping on structural and dielectric properties of PLZT ceramics
Rai R, Sharma S, Choudhary RNP
4267 - 4272 A systematic study on the growth of PZNT films by LPE method
Zeng XH, Qin F, Yao X, Xu NH, Xu S
4273 - 4284 Composition and crystal structure of resorbable calcium phosphate thin films
Tuck L, Sayer M, Mackenzie M, Hadermann J, Dunfield D, Pietak A, Reid JW, Stratilatov AD
4285 - 4292 A new indirect method of measuring the contents of solid inclusions in liquid aluminium alloys
Cao X
4293 - 4297 Corrosion and stress corrosion cracking behavior of equal channel angular pressed oxygen-free copper in 3.5% NaCl solution
Jang YH, Kim SS, Han SZ, Lim CY, Kim CJ
4299 - 4302 Effect of minor Sc and Zr addition on the mechanical properties of Friction Stir Processed 2024 aluminium alloy
Cavaliere P
4303 - 4306 Phase relationship in the Fe-Pt-Pr ternary system at 500 degrees C
Gu ZF, Cheng G, Ren J, Wang ZM, Zhou HY
4307 - 4313 Mechanical and fracture behavior of powder metallurgy processed Ti3Al-based alloys
Dimcic B, Cvijovic I, Jovanovic MT, Bozic D, Dimcic O
4315 - 4319 Waste glass and fly ash derived glass-ceramic
Yoon SD, Yun YH
4321 - 4326 Fibre-reinforced composite implant: in vitro mechanical interlocking with bone model material and residual monomer analysis
Mattila RH, Puska MA, Lassila LVJ, Vallittu PK
4327 - 4333 Electrical behaviour of materials based on monoclinic celsian derived from cation-exchanged commercial zeolites
Motori A, Patuelli F, Saccani A, Andreola F, Bondioli F, Siligardi C, Ferrari AM
4335 - 4341 Glycothermal synthesis of vanadiurn(III) phosphate hydrates
Nakamura T, Inui T, Inoue M, Miyake T
4343 - 4347 Designing biological apatite suitable for neomycin delivery
Murugan R, Ramakrishna S
4349 - 4356 Monitoring of cure kinetic prepreg and cure cycle modeling
Costa ML, Botelho EC, Rezende MC
4357 - 4364 Feasibility of three-dimensional macroporous scaffold using calcium phosphate glass and polyurethane sponge
Park YS, Kim KN, Kim KM, Choi SH, Kim CK, Legeros RZ, Lee YK
4365 - 4372 Methods for modelling the ultimate strength of orthotropic plate with a central hole under uniaxial tension
Arino SB, Frechin MM
4373 - 4373 Conductive percolation threshold of conductive-insulating granular composites (vol 41, pg 2157, 2006)
Ren L, Han Z, Tong J, Li J, Chen D, He D