Degradation mechanism of alkyl carbonate solvents used in lithium-ion cells during initial charging
Abstract
The degradation mechanism of electrolytes in the lithium-ion cell with LiCoO2 and graphite electrodes was investigated by analyzing: (i) the composition of generated gases; (ii) thin films formed on the electrode, and (iii) the compositional change of the electrolyte during the initial charging. The solvents in this work were ethylene carbonate (EC), dimethyl carbonate (DMC), ethylmethyl carbonate (EMC) and diethyl carbonate (DEC). LiPF6 was used as a salt. In the one- to three-component systems containing EC, carbon monoxide and ethane were detected, whereas Li2CO3, RCOOLi and (CH2OLi)2 were the main components of the surface film on the negative electrode. From these results, it can be assumed that the decomposition of the systems was mainly due to the reductive reaction of EC at the initial charging. Through the additional analysis of the electrolyte composition, it was confirmed that the dialkyl-2,5-dioxahexane carboxylate was produced in the electrolyte after initial charging. This suggests the occurrence of trans-esterification.
References (6)
- H. Yoshida et al.
Denki Kagaku
(1994) - Z.X. Shu et al.
J. Electrochem. Soc.
(1993) - R. Fong et al.
J. Electrochem. Soc.
(1990)
Cited by (223)
Thermal runaway evolution of a 280 Ah lithium-ion battery with LiFePO<inf>4</inf> as the cathode for different heat transfer modes constructed by mechanical abuse
2024, Journal of Energy ChemistryLithium iron phosphate batteries have been increasingly utilized in recent years because their higher safety performance can improve the increasing trend of recurring thermal runaway accidents. However, the safety performance and mechanism of high-capacity lithium iron phosphate batteries under internal short-circuit challenges remain to be explored. This work analyzes the thermal runaway evolution of high-capacity LiFePO4 batteries under different internal heat transfer modes, which are controlled by different penetration modes. Two penetration cases involving complete penetration and incomplete penetration were detected during the test, and two modes were performed incorporating nails that either remained or were removed after penetration to comprehensively reveal the thermal runaway mechanism. A theoretical model of microcircuits and internal heat conduction is also established. The results indicated three thermal runaway evolution processes for high-capacity batteries, which corresponded to the experimental results of thermal equilibrium, single thermal runaway, and two thermal runaway events. The difference in heat distribution in the three phenomena is determined based on the microstructure and material structure near the pinhole. By controlling the heat dissipation conditions, the time interval between two thermal runaway events can be delayed from 558 to 1417 s, accompanied by a decrease in the concentration of in-situ gas production during the second thermal runaway event.
Research on the lower explosion limit of thermal runaway gas in lithium batteries under high-temperature and slight overcharge conditions
2024, Journal of Energy StorageLithium battery thermal runaway release a large amount of flammable gas, which often triggers secondary explosions at high temperatures. Slight overcharge can lead to an increase in the risk of thermal runaway gas, and different charge and discharge temperature environments have a great impact on the thermal runaway gas of overcharged batteries. In this paper, the lower explosion limits of thermal runaway gas of lithium batteries under different charging and discharging environments are studied, and corresponding guidelines are proposed for the safe use of lithium batteries. The experimental results show that overcharging leads to a decrease in the Lower Explosion Limit (LEL) of thermal runaway gas. The charge/discharge temperature environment also has an effect on the thermal runaway gas LEL of the battery, and the lowest thermal runaway gas explosion lower limit is found for the battery charged and discharged at a temperature environment of 40 °C. The decrease of thermal runaway gas LEL is due to the decrease of CO2 content in the gas and the increase of vaporized Differential Scanning Calorimetry (DMC) content, and the increase of vaporized DMC content in the gas mixture is due to the precipitation of lithium in the negative electrode material.
Development and application of a semi-detailed model for lithium-Ion battery thermal runaway chemistry
2024, Applied Thermal EngineeringTo overcome the disadvantages of detailed methodologies and existing simple methodologies for modeling lithium-ion battery thermal runaway chemistry, a semi-detailed model has been developed in the present work. This is important for mitigating battery thermal runaway. The semi-detailed model contains two parts: a ‘global part’ and an ‘elementary reaction mechanism part’. The thermal kinetics parameters of a recently published model are improved so that it can be selected for the ‘global part’ to model NCM811 (LiNi0.8Co0.1Mn0.1O2), NCM622 (LiNi0.6Co0.2Mn0.2O2), and NCM532 (LiNi0.5Co0.3Mn0.2O2). Temperature and heat release evolutions during battery thermal runaway can be obtained from the simulation of the ‘global part’. In the ‘elementary reaction mechanism part’, 53 reactions with frequency factors and activation energies have been proposed and adopted for describing flammable gas formation, lithium-ion consumption, gas phase interaction, and lithium-ion gas interaction during battery thermal runway. Detailed processes for coupling the ‘global part’ and the ‘elementary reaction mechanism part’ as well as solving the 53 reactions are developed, which is the major novelty of this work. Through the coupling of the two parts, chemical venting gas species generation and lithium-ion consumption during the transient thermal runaway process of an NCM811PC (LiNi0.8Co0.1Mn0.1O2 polycrystalline) pouch cell with nail penetration were calculated and compared with available experimental data in the literature. The comparison shows that the semi-detailed model can give correct species trends, indicating the two parts and their coupling in the semi-detailed model of the present work are reliable. The simulation results with transient venting gas chemical species provide useful insights for stopping or delaying battery thermal runaway.
Experimental study on exploration of optimum extinguishing agent for 243 Ah lithium iron phosphate battery fires
2023, Process Safety and Environmental ProtectionNowadays, an effective and clean extinguishing agent or technology is highly desirable for lithium-ion battery (LIB) fires. Herein, the physicochemical properties and extinguishing effects of various extinguishing agents on 243 Ah lithium iron phosphate (LFP) battery fires are investigated systematically. The extinguishing mechanisms are deeply analyzed and the performance is comprehensively evaluated from the aspects of thermal runaway (TR) and toxicity suppression, cooling and extinguishing efficiency. Compared with HFC-227ea, C6F12O can absorb more heat through vaporization, thereby improving extinguishing and cooling efficiency. The lack of chemical inhibition effect and the tiny droplet size make water mist unable to suppress the high-temperature jet fire, but it has the lowest toxicity and highest cooling efficiency of 54.6%. F-500 and FireIce can improve the extinguishing performance of the water mist by encapsulating and taking hydrocarbon fuel away from the fire zone and inhibiting free radicals in the flame, respectively. 3% F-500 has the extinguishing efficiency of 78.4% and TR efficiency of 64.1%, while maintaining the cooling performance well. In the future, a novel type of fire-extinguishing agent with high heat capacity and latent heat, excellent extinguishing performance, high wettability, low toxicity and insulating properties is expected to be developed for LIB fires.
Hydrogen gas diffusion behavior and detector installation optimization of lithium ion battery energy-storage cabin
2023, Journal of Energy StorageH2 and CO are regarded as effective early safety-warning gases for preventing battery thermal runaway accidents. However, heat dissipation systems and dense accumulation of batteries in energy-storage systems lead to complex diffusion behaviors of characteristic gases. The detector installation position significantly affects the gas detection time. We conducted a gas diffusion behavior study and proposed a detection position optimization method through experiments and simulations. The gas warning effectiveness and accuracy of the simulations were experimentally verified. The results showed that an H2 detector at the top of the cabin could warn 145 s before thermal runaway. To shorten the detection time, nearly one hundred gas diffusion simulations were performed. The detector installation strategy was explored using integer programming; the results showed that installing 3–5 detectors in the cabin was optimal. The detection time with three detectors was 116.43 s shorter than with one detector. The experimental and simulation results indicate an effective gas detector installation method for early safety warnings in energy-storage cabins.
Failure and hazard characterisation of high-power lithium-ion cells via coupling accelerating rate calorimetry with in-line mass spectrometry, statistical and post-mortem analyses
2023, Journal of Energy StorageLithium-ion battery safety continues to be an obstacle for electric vehicles and electrified aerospace. Cell failure must be studied in order to engineer improved cells, battery packs and management systems. In this work, the thermal runaway of commercially available, high-power cells is studied, to understand the optimal areas to develop mitigation strategies. Accelerating rate calorimetry is coupled with mass spectrometry to examine self-heating and the corresponding evolution of gases. A statistical analysis of cell failure is then conducted, combined with post-mortem examinations. The methodology forms a robust assessment of cell failure, including the expected worst- and best-cases, and the associated real-world hazards. Cells produce a highly flammable, toxic gas mixture which varies over the course of self-heating. Failure also produces particulate matter which poses a severe health hazard. Critically, the onset of self-heating is detectable more than a day in advance of full thermal runaway. Likewise, voltage drops and leaks are detectable prior to venting, highlighting the potential for highly effective early onset detection. Furthermore, the behaviour of the cap during thermal runaway indicates that ejection of material likely reduces the chance of thermal runaway propagation to neighbouring cells. These findings also emphasise that research must be conducted safely.